熱門產品
關于我們
聯系我們
升降貨梯http://www.jntr168.com/安裝儲罐的基礎要求平整，并能承受相應的壓力。儲罐安裝設備在出廠時已安裝好了接頭，強度是最佳的。但在運輸、裝卸時接頭可能會引起松動，宜在安裝時對接頭密封性能進行檢查。
Cargo lifter installed base of the tank should be smooth, and can withstand the corresponding pressure. Tank install equipment at the factory installed the joint strength is the best. But in the transport, handling may cause loose
joints, should be in the installation of the Joints to be checked.
在升降貨梯先期施工的罐底板上安裝數個固定墊墩，然后組裝第一層壁板和頂蓋板，沿罐內壁400mm處均布數臺液壓提升機，以提升機的滑動托架托住固定在罐內壁的脹圈下部，操縱液壓提升機的控制距。
Pre-installed on a cargo lifter construction of the tank floor mat several fixed pier, then assembled the first layer of wall and roof panels, along the tank wall at a uniform number of 400mm hydraulic hoist to lift up the machine to enhance the sliding bracket fixed in the lower part of the tank wall expansion ring, hydraulic steering control from the hoist.
升降貨梯http://www.jntr168.com/在使用過程中需要檢查安裝盲板，盲板要安裝在最靠近儲罐的法蘭處。盲板要安裝在截止閥最適合進行試壓的一側，盲板兩側應安裝密封墊圈，按照需要至少在盲板的受壓一側要加密封墊圈。工作人員能否到達所選擇的 儲罐安裝設備盲板安裝位置，是否制定了消除或減少跑冒滴漏、防止污染的有關規定。盲板是否安裝在最靠近設備、儲罐或容器的法蘭處。對升降貨梯儲罐檢修時，如需現場射線探傷時，應隔離出透照區，設置安全標志。
Cargo lifter in the course you need to check the installation Blind, blind flange to be installed closest to the tank. Blind side of the shut-off valve must be installed in the most suitable for the pressure test, should be installed on both sides of the blind plate gasket, according to at least one side of the blind in the pressure plate to add gasket. Staff can reach the selected tank installations Blind installation location, whether formulated to eliminate or reduce leaking, to prevent contamination of the relevant provisions. Blind flange plate is installed in the closest device, tank or vessel. When cargo lifter tank for maintenance, while for site-ray detection, should isolate the transillumination area, set up safety signs.
